Monthly Archives: February 2012

Vulerability of Traditional Telephone Lines


Over 90% of existing home security systems depend on the phone line. Traditionally  alarm systems used the phone line to connect to a staffed central station that monitors whether the system has recorded an “incident,” such as a possible break-in. After receipt of an alarm signal, the station attempts to call the property owner to determine if an emergency has occurred, and then contacts law enforcement if it can’t verify that the alarm is false.

Alarmingly, if the phone line is cut, it is unlikely that a signal could be transmitted to the monitoring center.

How Can a Traditional Alarm System be Defeated?

There are other ways to disable most alarm systems: an intruder can smash the alarm device if they can locate it, especially when it’s readily visible near the entrance or easily accessible from first floor windows. And that’s where most intruders gain entry. One home security survey in Pennsylvania concluded that more than 80 percent of residential intrusions occurred through the first floor, most of those through the front door or through a first-floor window.

Most alarm systems have an “entry” delay of approximately 30 seconds between recognizing that a door or window has been opened and when the siren sounds – and then an additional 30 seconds before sending the signal on to the central station. The delays are built-in to provide time for the homeowner to turn off the alarm after they’ve entered the house, and even after the siren sounds. But that same delay also allows an intruder time to find and destroy the alarm system’s control panel before it can notify the central station.

Cellular Alarm Systems Are Safer


With the Burns & McBride Go! Control, there is no traditional phone line connection, so the system can’t be disabled by cutting an outdoor phone wire.  We use a built in cell phone. Our wireless home security system sends an alert signal to the central station immediately after a door or window has been opened so it is almost immediately aware of the potential for a security incident.  Motion detectors can also be placed inside and outside the home, so visits to the home can be monitored and recorded online even before someone might attempt to disable an alarm and break in. Plus, if the burglar should try to knock the Go!Control box off the wall or break it in any way – our exclusive “Smash and Crash” protection immediately sends an alarm.

The wireless option is relatively new, but gaining in popularity.  In fact more and more homes don’t even have a traditional telephone line as we all switch to cell phones.

And you’re not the only one who has seen the many movie plots when the alarm wires get snipped.

The burglar has seen them, too.

For more information on this exciting product call us at 302-656-5110 or visit our website at http://www.burnsandmcbride. Finally you might want to follow our blog at http://www.burnsandmcbrideblog.com. Just as Smartphones are adding applications and changing every day so to with the technology behind our Smart, Safe home system. Our blog explains some of the constantly changing things that are happening in the industry and we hope that you find it informative.

Leave a comment

Filed under Home Safety, Home Security, Uncategorized

Home Security 101 – Text Messages Let You Know What’s Going On At Home!



A Burns & McBride Smart, Safe Home System will do more than just notify the police or fire department of life safety emergencies.

It can keep you in touch with anything happening at home. In addition to alerting you of an unwanted intrusion, your system should also alert you when the kids got home from school, when a liquor or gun cabinet was opened or even if the heat is off.  Here are some more: did someone disarm the system? Who was it – and when? All this information (and more!) can be sent to you almost instantly, and to anyone else you want to receive your alert signals.

How do notifications work?

Every time a sensor in your home is activated, it sends a signal to your alarm control panel – and the control panel forwards that signal to you over the cellular link  You can get alerts each time a door opens or a motion sensor is activated. And you can even put a micro sensor on “sensitive” locations like a medicine cabinet, liquor closet, or gun safe. Additionally, “No-Show” alerts can notify you by text or email if your alarm system is NOT disarmed in a specified window of time. This is a great solution to ensure that kids are getting home on time after school.

For more information on this exciting product call us at 302-656-5110 or visit our website at http://www.burnsandmcbride. Finally you might want to follow our blog at http://www.burnsandmcbrideblog.com. Just as Smartphones are adding applications and changing every day so to with the technology behind our Smart, Safe home system. Our blog explains some of the constantly changing things that are happening in the industry and we hope that you find it informative.

Leave a comment

Filed under Energy Management, Home Safety, Home Security, Home Security 101, Uncategorized

Who’s Monitoring YOUR Alarm System 24/7?


Most alarm companies like to brag about their 24/7 monitoring center: each center (also called a “central station”) is faster, better, more secure, more responsive, more reliable than the next – you’ve probably seen the ads, or heard the pitch. Well we’d like to brag a little ourselves. It’s worth learning what really matters in monitoring, and what separates the good from the bad, when it comes to who is responding to your alarm events.

First, here is a reminder on how the alarm process works:

1) Your alarm control panel receives an alarm signal from a sensor in your home.

2) If not quickly disarmed, the control panel sends the alarm event signal to the monitoring center. With the safest systems this happens over a cellular connection, not a vulnerable phone line.

3) The monitoring center calls you to verify if it’s a real alarm (asking for your passcode).

4) If the monitoring center cannot reach you (or does not get the passcode), they dispatch police, fire, or medical, depending on the specific signal they received.

So what makes one monitoring center better than another? There are several points of differentiation, and here’s what I think they are.

  • Approvals and Licensing – The critical ones are UL, Factory Mutual, Department of Defense (DOD) clearance, and Fire Department of New York – only a handful in the US have FDNY approval. Once achieved, these levels of compliance must be met year after year. In many states and local jurisdictions, central stations need their own licenses to offer services.
  • System redundancy – The point is not how many centers a company has, but how robust each center’s infrastructure is. Redundant primary and backup power, telecommunications (access & carriers), web access, servers, even backup HVAC contribute to providing flawless response.
  • Training and employee retention – What caliber of operator is hired, how well are they trained and managed, and how long do they stay? Even with the best systems, it is ultimately people who are verifying alarms and dispatching the authorities.
  • Experience and track record – It takes a center time to learn how to monitor well. The best centers have been around for a while, have perfected their hardware and software, and know how to react efficiently and effectively. You will know when you are talking to a good center – and it won’t take long for them to call, after the alarm event.

Some alarm companies have their own monitoring centers, and some use a third party that specializes in monitoring. Both solutions work. The third party companies have a lot to offer vs. the in-house center: monitoring is all these centers do, so they tend to be really focused on it, and good at it. There are also companies who make a big deal about multiple centers, backing each other up: this sounds good on paper, but when one of their centers actually goes down, you can learn the hard way how well the centers share information and route calls in an emergency. As mentioned above, the best architecture is the highest level of redundancy in each center itself, so that multiple center redundancy is not required.

Burns & McBride Home Comfort chose Rapid Response Monitoring, and we consider Rapid to be the best in the industry. Founded in 1992, they have all the right licenses and approvals – and yes, they are one of those select companies who can monitor commercial fire alarms in New York City, which is the toughest approval in the industry.

For more information on this exciting product call us at 302-656-5110 or visit our website at http://www.burnsandmcbride. Finally you might want to follow our blog at http://www.burnsandmcbrideblog.com. Just as Smartphones are adding applications and changing every day so to with the technology behind our Smart, Safe home system. Our blog explains some of the constantly changing things that are happening in the industry and we hope that you find it informative.

Leave a comment

Filed under Energy Management, Home Safety, Home Security, Uncategorized

Home Security 101 – What is a Motion Detector?


There is definitely some mystery surrounding motion sensors. They are a core element of most alarm systems and a standard feature ion our Smart, Safe Home package. So, let’s dig into what they really do.

Motion sensors detect and report motion – in most cases when nobody is home (Armed-Away). That’s why they are not “awake” when you arm your system for the night (Armed-Stay) . It’s usually not practical to put a sensor on every window, and you usually don’t need to, since you can use motion sensors and glass break detectors to get the protection you need more affordably. Plus, motion sensors have come a long way from the original models – much more reliable, and less prone to false alarms.

How do they work?

The early motion sensors were considered “active” devices, because they emitted energy (microwave or ultrasonic) to see what was happening around them. There are some still some microwave sensors being installed in commercial spaces. Today the most common motion sensor uses Passive Infra-Red energy to detect heat given off by people (and animals!) – hence the name “PIR” given to the device. The smart detectors look for objects warmer than the normal background temperature, using a special lens to create “beams” of passive energy, and then look for motion: when the sensor detects a “warm” object moving across several beams within a specified time frame – that trips the alarm.

Where do you use them?

The standard range is 30-35 feet, and the coverage area is shaped like a large water droplet, with the skinny part at the detector. The ideal spot for a motion sensor is in a high-traffic area that an intruder would cross if moving about in your home or business: think hallways, living rooms with big-screen TV, etc. The sensors work better when people move across the beams, as opposed to approaching the sensor directly. The beams project out and down, to pick up anyone trying to avoid detection by crawling.

Motion sensors and pets

Today’s sensors are usually “pet-friendly” up to 40 pounds, which means they “ignore” cats and small dogs – unless your Siamese is downright acrobatic! That means that large dogs with the run of the house all day and night make it harder to use motion sensors – unless you kennel them!

 Things to Remember

Manufacturers recommend careful placement of their products to prevent false (non-intruder caused) alarms. They suggest mounting the PIDs in such a way that the PIR cannot ‘see’ out of a window. Although the wavelength of infrared radiation to which the chips are sensitive does not penetrate glass very well, a strong infrared source such as from a vehicle headlight or sunlight reflecting from a vehicle window can overload the chip with enough infrared energy to fool the electronics and cause a false alarm. A person moving on the other side of the glass however would not be ‘seen’ by the PIR.

They also recommended that the PIR not be placed in such a position that an heating and air conditioning vent would blow hot or cold air onto the surface of the plastic which covers the housing’s window. Although air emits very small amounts of infrared energy, the air blowing on the plastic window cover could change the plastic’s temperature enough to, once again, fool the electronic

Specifications

Based on the latest in infrared technology, the Burns & McBride motion detector comes with three different mounting brackets and a 90° lookdown, ensuring intruders cannot pass by unnoticed. It also communicates directly with tyour Burns & McBride Go!Control panel, so if the detector is triggered, the panel will connect you to the central monitoring station in as few as 17 seconds.

Dimensions and weight
  • Width: 2.5″
  • Height: 3.2″
  • Depth: 1.9″
  • Weight (including battery and brackets): 3.7 oz. (104.9 g)

Regulatory Listing(s)

  • ETL, FCC Part 15, Industry Canada
Features
  • 90° lookdown
  • 110° wide-angle spread
  • Three different mounting brackets
  • 30’x50′ range
  • 33–55 lb. pet immune
  • Five-year lithium battery
  • Tamper-protected
Benefits
  • 90° lookdown: Ensure that no one can walk beneath your sensor undetected
  • Tamper–proof: Know when someone is trying to tamper with your alarm
  • Fully monitored: Get connected to the Burns & McBride central monitoring station in as few as 17 seconds
Radio
  • Wireless signal range
  • 350 ft., open air, with 2GIG Wireless Alarm Control Panel
  • Transmitter Frequency
  • 345.000 MHz (crystal controlled)
  • Transmitter Frequency Tolerance
  • ± 15 kHz
  • Transmitter Bandwidth
  • 24 kHz
  • Modulation Type
  • Amplitude Shift Keying—On/Off Keying (ASK-OOK)
  • Peak Field Strength
  • Typical 50,000 uV/m at 3m
Housing
  • Material
  • ABS plastic and poly-carbonate
  • Color
  • White
  • Operating temperature
  • 32° to 120°F (0° to 49°C)
  • Relative Humidity
  • 5-95% Non-Condensing
  • Unique ID Codes
  • Over one (1) million different code combinations
  • Supervisory Interval
  • 70 minutes
Warranty
  • Lifetime
Included equipment and accessories
  • Battery (installed)
  • Two (2) Panasonic CR2032, or equivalent Lithium batteries
  • Included Accessories
  • Mounting brackets, two (2) long Phillip’s head screws, two (2) plastic wall anchors, magnet

For more information on this exciting product call us at 302-656-5110 or visit our website at http://www.burnsandmcbride. Finally you might want to follow our blog at http://www.burnsandmcbrideblog.com. Just as Smartphones are adding applications and changing every day so to with the technology behind our Smart, Safe home system. Our blog explains some of the constantly changing things that are happening in the industry and we hope that you find it informative.

Leave a comment

Filed under Home Safety, Home Security, Home Security 101, How Things Work, Uncategorized